DOT inspection checklist: annual inspection, pre-trip and trailer forms
Print a DOT inspection checklist for the annual inspection, pre-trip and trailers, built from 49 CFR Part 396, with who needs one and how long to keep it.
Start from the work orders template
Take requests, assign jobs, track them to done.
On this page
If a truck, or a truck and trailer together, is rated 10,001 pounds or more and used across state lines for business, federal rules require an inspection by a qualified inspector at least every 12 months, a driver check before each trip and a written report of any defect. Trucks that stay in one state follow that state’s rules.
It’s for owners, fleet managers and shop leads at trucking, construction, landscaping and trailer businesses that run vehicles under Department of Transportation (DOT) rules. A 6,000-pound pickup towing a 5,000-pound trailer is an 11,000-pound combination, and a job across a state line makes it interstate. Below: the annual inspection as a form to print, who is covered, who may inspect and what to keep, the pre-trip check and driver’s report, a trailer checklist and roadside levels. For the daily walk-around, see our vehicle inspection checklist. To track each unit’s due date, GoodTaco’s work order template has repeating jobs.
How we researched this: checked November 2026, in the Electronic Code of Federal Regulations (eCFR), current through November 10, 2026, and in the Commercial Vehicle Safety Alliance’s (CVSA) own roadside inspection policy. This guide isn’t legal advice. Ask the Federal Motor Carrier Safety Administration (FMCSA) or your state’s transportation department about your own fleet.
DOT annual inspection checklist: the form, item by item
A DOT officer doesn’t perform the annual inspection. You pick the inspector, and the carrier is responsible for it. Section 396.17 says the inspection must cover at least the parts in Appendix A to Part 396, the minimum periodic inspection standards. (Older forms call it Appendix G to Subchapter B; FMCSA renumbered it in October 2021.) Section 396.21 lists what the report must say but not how it’s laid out, so a plain sheet works.
Print this page and use one sheet per vehicle. Each trailer is its own vehicle. Tick OK, Def (defect) or N/A on each line.
ANNUAL INSPECTION
Carrier: ____________________
Unit: ______ Type: _________
Plate / ID no.: _____________
Date: _______________________
Inspector: __________________
Shop or yard: _______________
OK Def N/A
[ ] [ ] [ ] 1a Service brakes
[ ] [ ] [ ] 1b Parking brake
[ ] [ ] [ ] 1c Drums, rotors
[ ] [ ] [ ] 1d Brake hoses
[ ] [ ] [ ] 1e Brake tubing
[ ] [ ] [ ] 1f Low-air warning
[ ] [ ] [ ] 1g Tractor prot. valve
[ ] [ ] [ ] 1h Air compressor
[ ] [ ] [ ] 1i Electric brakes
[ ] [ ] [ ] 1j Hydraulic brakes
[ ] [ ] [ ] 1k Vacuum system
[ ] [ ] [ ] 1l ABS
[ ] [ ] [ ] 1m Auto adjusters
[ ] [ ] [ ] 2 Coupling devices
[ ] [ ] [ ] 3 Exhaust
[ ] [ ] [ ] 4 Fuel system
[ ] [ ] [ ] 5 Lights, reflectors
[ ] [ ] [ ] 6 Safe loading
[ ] [ ] [ ] 7 Steering
[ ] [ ] [ ] 8 Suspension
[ ] [ ] [ ] 9 Frame
[ ] [ ] [ ] 10 Tires
[ ] [ ] [ ] 11 Wheels, rims
[ ] [ ] [ ] 12 Windshield glass
[ ] [ ] [ ] 13 Wipers
[ ] [ ] [ ] 14 Bus seats
[ ] [ ] [ ] 15 Rear impact guard
Defects (item, what's wrong):
______________________________
______________________________
Repaired by: ________________
Date repaired: ______________
I certify this inspection is
accurate and complete.
Signature: __________________
Date: _______________________
Marking a trailer? Parts it doesn’t have, such as the compressor, exhaust, fuel, steering, windshield and wipers, are N/A. Electric brakes go under 1i.
Appendix A is the full list, and a shop works from its text. This table sums up what fails each part. The numbers are the Appendix A item numbers.
| Part | Fails the inspection if |
|---|---|
| 1a Service brakes | No braking on an axle that needs it, an air leak at a chamber, lining under 1/4 inch on air drum brakes, or pushrod stroke past the limit |
| 1b Parking brake | No brakes apply when the control is pulled |
| 1d, 1e Hoses and tubing | Any audible leak, a bulge under pressure, damage through the outer ply, or cracked or crimped |
| 1f, 1l Warning and ABS | Low-pressure warning missing or not working at 55 psi; ABS lamp doesn’t light at start-up, or stays on |
| 1m Automatic adjusters | Replaced with a manual adjuster, or a brake out of adjustment and the cause not fixed |
| 2 Coupling devices | Fifth wheel play over 1/2 inch, kingpin not engaged, a cracked or welded pintle hook, or worn chains |
| 3, 4 Exhaust and fuel | Exhaust leaking ahead of or below the cab, a fuel leak, a missing cap, or a loose tank |
| 5 Lighting | Any light or reflector that Part 393 requires isn’t working |
| 7 Steering | Wheel free play past the limit, cracks or welded repairs on steering parts, or loose nuts |
| 8, 9 Suspension and frame | A broken main leaf, a deflated air suspension, or a cracked or sagging frame member |
| 10 Tires | Steering axle under 4/32 inch, other tires under 2/32, exposed cord, flat or leaking |
| 11 Wheels and rims | A cracked rim, elongated bolt holes, loose or missing fasteners, or cracked welds |
| 12, 13 Glass and wipers | A crack or vision-reducing damage beyond the minor ones Appendix A allows; a wiper that doesn’t work |
| 6 Safe loading | A spare tire or the load could fall onto the road |
| 15 Rear impact guard | Missing or loose; on a trailer of 10,001 pounds or more built since Jan 26, 1998, a bar over 22 inches high |
The tread limits match 393.75. It’s the minimum, so add your own lines for oil leaks, mirrors and the battery. Under 396.17(g), you’re responsible for repairing a failed part promptly, and a truck that’s unsafe to drive stays parked (396.7). Skipping the inspection can bring fines under 49 U.S.C. 521(b); FMCSA sets the amounts.
Which trucks and trailers need a DOT inspection?
The rules are in Part 396 of the Federal Motor Carrier Safety Regulations. They apply to every motor carrier, for-hire or private, so a contractor who hauls their own equipment counts (390.5T). A vehicle is a commercial motor vehicle when it’s used on a highway in interstate commerce to move people or property and any of these is true:
- Weight: its weight rating, or its actual weight, is 10,001 pounds or more. For a truck towing a trailer, the combination rating is the sum of both ratings, or the manufacturer’s combination rating if that’s higher.
- Passengers: it’s designed or used to carry more than 8 people for pay, or more than 15 people not for pay, counting the driver.
- Hazardous materials: it carries them in a quantity that needs placards.
Interstate commerce includes a trip inside one state that is part of a shipment coming from or going to another state. Trucks that never do that follow their state’s rules, which may differ from these. A state may exempt some in-state vehicles under 26,001 pounds (350.305), so ask your state’s highway patrol or transportation department. Part 396 also doesn’t cover covered farm vehicles (396.1(c)), transportation performed by a government, or the occasional hauling of personal property that isn’t for pay or business (390.3T(f)).
| Check | Who, and when | Keep it |
|---|---|---|
| Pre-trip | Driver, before driving | No record of the check itself |
| Driver vehicle inspection report | Driver, end of each day, if there’s a defect | 3 months |
| Annual inspection | Qualified inspector, every 12 months | Report 14 months |
Who can do the DOT annual inspection, and what must the report say?
Who does it:
- Your own shop, or someone else’s. A carrier can inspect its own vehicles, or have a commercial garage, fleet leasing company, truck stop or similar business do it, if that business has facilities suited to commercial vehicle inspections and qualified inspectors (396.17(d) and (e)).
- A qualified inspector. They know Part 393 and Appendix A, can spot a defective part and have mastered the tools, and they either finished a federal- or state-sponsored training program (or hold a state certificate) or have at least a year of training or experience as a mechanic or inspector (396.19). Keep evidence of it while they inspect for you and for one year after, unless it’s a state program inspection.
- Brake work has its own bar. People responsible for inspecting or repairing brakes must meet the qualifications in 396.25.
- A state inspection can count. A passing periodic inspection run by a state, if it meets Appendix A, counts for 12 months from the last day of the month it was done (396.17(f)).
The inspector’s report must identify:
- the inspector,
- the motor carrier,
- the date,
- the vehicle,
- each component inspected and the result, including any that don’t meet Appendix A, and
- a certification that the report is accurate and complete (396.21(a)).
Proof on the vehicle. The vehicle can’t be used unless every Appendix A component passed in the last 12 months and proof is on the vehicle. The proof is the report itself, or a sticker or decal with the inspection date, where the report is kept, the vehicle’s ID if it isn’t marked, and a certification that it passed (396.17(c)).
What’s the difference between a DOT pre-trip inspection and a DVIR?
They cover the same 11 parts, and the driver vehicle inspection report is called a DVIR for short: service brakes including trailer brake connections, parking brake, steering, lights and reflectors, tires, horn, windshield wipers, mirrors, coupling devices, wheels and rims, and emergency equipment. They’re different duties.
| Pre-trip | DVIR | |
|---|---|---|
| Rule | 392.7, 396.13 | 396.11 |
| Who | The driver | The driver writes it; the carrier repairs and certifies |
| When | Before driving | End of each day’s work |
| In writing? | No | Only if there’s a defect |
| Keep | Nothing for the check; the driver’s sign-off on a DVIR is kept with it | 3 months |
Before driving, the driver must be satisfied that the vehicle is safe. If the last DVIR listed a defect, the driver reviews it and signs that the repairs were certified (396.13). A DVIR names the vehicle, lists each defect that would affect safe operation or cause a breakdown, and is signed by the driver. If nothing was found, no report is needed. Before the vehicle runs again, the carrier repairs any listed defect likely to affect safety and certifies on the report that it was repaired or didn’t need repair. Keep the report, the certification and the driver’s review for 3 months. Electronic reports count (390.32). The rule doesn’t ask for a written pre-trip record, though your insurer or company policy may.
A carrier that runs only one commercial motor vehicle doesn’t need DVIRs. Neither do driveaway-towaway operations, such as delivering an empty vehicle to a dealer, or private passenger carriers that aren’t a business (396.11(a)(5)).
DOT trailer inspection checklist and requirements
Yes, a trailer is inspected when it’s part of a commercial motor vehicle combination. The weight test uses the combination’s rating, and 396.17(a) says the term includes each vehicle in a combination: the tractor, the semitrailer, the full trailer and any converter dolly. So a dump or equipment trailer behind a covered truck gets its own annual inspection, its own unit number and its own sheet. The rule doesn’t separately say whether that holds for a trailer rated under 10,001 pounds; ask FMCSA or your state, and until you have an answer, inspect it with the truck.
Appendix A items for trailers, plus the brake rules that matter most:
| Trailer part | Fails the inspection if |
|---|---|
| Brakes | A brake missing where one is required, or no braking on a wheel |
| Breakaway brakes | They don’t apply on separation, or don’t stay applied 15 minutes |
| Breakaway device (electric brakes) | Missing or inoperable |
| ABS lamp | A trailer’s lamp doesn’t cycle when power is applied |
| Air lines | Any audible leak, or a cracked or crimped hose |
| Safety chains or cables | Missing, worn, or repaired with wire, rope or tape |
| Fifth wheel, kingpin, pintle hook | Light shows between the halves, kingpin not engaged, or a cracked or welded hook |
| Lights and reflectors | Any that Part 393 requires isn’t working |
| Tires and wheels | Same limits as the truck: under 2/32 inch, exposed cord, flat, overloaded |
| Rear impact guard | Missing or loose, or on trailers of 10,001 pounds or more built since Jan 26, 1998, a bar over 22 inches high |
| Frame and suspension | A cracked or sagging frame member, broken springs, loose U-bolts |
The sources are Appendix A and 393.42 (a trailer weighing 3,000 pounds or less can be exempt from brakes under conditions), 393.43(d) (breakaway) and 393.70(d) (safety devices on full trailers). Landing gear, ramps, doors and cargo securement aren’t on Appendix A, but CVSA lists cargo securement as a critical item at a roadside inspection, so check them in the daily walk-around. A trailer that isn’t a commercial motor vehicle still has to meet state lighting and equipment rules.
How long do you keep DOT inspection records?
| Record | How long | Rule |
|---|---|---|
| Driver vehicle inspection report, repair certification, driver’s review | 3 months | 396.11(a)(4) |
| Maintenance, inspection and repair records | 1 year, and 6 months after the vehicle leaves your control | 396.3(c) |
| Annual inspection report | 14 months | 396.21(b) |
| Roadside inspection report copy | 12 months | 396.9(d) |
| Inspector’s qualifications | While they inspect, plus 1 year | 396.19(b) |
The annual report and the maintenance records are kept where the vehicle is housed or maintained. Section 396.3(b) also asks for a way to show the nature and due date of each inspection and maintenance job, which is what a due-date list does. Our equipment maintenance log guide shows what those records hold.
What happens at a DOT roadside inspection?
Roadside inspectors use the CVSA’s North American Standard inspection levels (Operational Policy 5, revised April 23, 2026). The ones a small fleet meets:
| Level | What’s checked |
|---|---|
| I | The driver’s license, medical certificate, hours of service and vehicle inspection reports, plus the vehicle: brakes, cargo securement, coupling devices, frame, fuel, lights, steering, suspension, tires, wheels |
| II | The same items, but only what can be seen without getting under the vehicle |
| III | The driver and paperwork only, including vehicle inspection reports |
| V | The vehicle only, with no driver present, at any location |
The rest are special inspections, radioactive shipments, jurisdiction-mandated programs, electronic inspections and post-crash inspections. Only a Level I or Level V inspection can earn a CVSA decal, which stays valid for up to three months and generally spares the vehicle another inspection in that time. It isn’t the annual inspection proof from 396.17(c).
A vehicle that would likely cause a crash or breakdown is declared out of service and marked with a sticker. Nobody may drive it, or tow it other than on a hoist or crane, until the repairs are done, and the carrier must certify the corrections on the inspection report within 15 days (396.9).
CVSA’s International Roadcheck is a three-day inspection event. The next one is scheduled for May 11 to 13, 2027. The 2026 event ran May 12 to 14, with cargo securement as the vehicle focus and electronic logging device tampering as the driver focus.
Track every annual inspection with GoodTaco
Prefer paper or a spreadsheet? Our free work order template comes in Word, Excel and PDF.
Nine trucks and nine trailers is 18 annual inspections, each running out on a different day. Miss one and that unit can’t be used until it’s inspected. GoodTaco’s work order template keeps the dates, so the shop is booked before 12 months run out. Sign up free and you get your own copy, with sample records you can rename or clear. Add your yards as sites and your trucks and trailers as equipment; the prompt below sets it up for a fleet.
Here’s an example with six units as of November 13, 2026:
| Unit | Last passed | 12 months end | Days left |
|---|---|---|---|
| TR-4801 | Nov 20, 2025 | Nov 20, 2026 | 7 |
| T-32 | Dec 4, 2025 | Dec 4, 2026 | 21 |
| T-33 | Jan 22, 2026 | Jan 22, 2027 | 70 |
| TR-4802 | Feb 9, 2026 | Feb 9, 2027 | 88 |
| T-31 | Mar 12, 2026 | Mar 12, 2027 | 119 |
| TR-4803 | Oct 2, 2026 | Oct 2, 2027 | 323 |
Add one repeating job per unit, every 12 months, and set “Next due” a couple of weeks before that unit’s 12 months run out, so a late shop slot doesn’t cost you the proof. Change the days ahead from 7 to 30. The work order is created that many days before it’s due, when someone on your team who can edit opens the app, and it lands in the assigned person’s My work. Open the app each Monday: that’s when due jobs get their work orders. The next date moves forward from the date it was due, not from the day the shop finished.
When a unit fails, the defect becomes a work order: the part, a priority and a due date. The template has four priorities: Urgent is due the same day, High the next day, Normal within 7 days and Low within 14. Finishing the job records what was done, the hours and the parts cost, and each unit’s page keeps its repairs. File the signed inspection report with the unit, where 396.21 says to; the app shows when it’s due, and the paper stays your record. For oil changes and other regular services, add repeating jobs from the preventive maintenance checklist.
To make it read like a fleet, ask GoodTaco in plain words:
Add Truck and Trailer as equipment categories. On each unit, add Plate, Vehicle ID number, Annual inspection date and Inspector. Show an Out of service switch on each unit’s page.
Every version is saved, so you can roll back with one click. The app opens in any browser, including a phone’s.
GoodTaco is free to start. Paid plans start at $9 a month, and Pro at $49 a month includes 10 users; bigger teams talk to us about Enterprise.
If your units already live in a spreadsheet, try our spreadsheet to app upload; no account needed, and the records go into the app’s own built-in database.
Put every unit’s inspection date in one place. Start free, no credit card needed.
Frequently asked questions
What is a DOT inspection checklist?
A list of the parts that federal rules make you check and sign for on a commercial truck or trailer. The driver checks the vehicle before each trip, writes a report at the end of the day if something is wrong, and a qualified inspector inspects it at least once every 12 months. The rules are in 49 CFR Part 396, and the annual inspection uses the list in Appendix A to Part 396.
How often does a truck or trailer need a DOT inspection?
At least once every 12 months. Under 49 CFR 396.17, a motor carrier can't use a commercial motor vehicle unless each part in Appendix A has passed an inspection in the last 12 months and proof of it is on the vehicle. Each vehicle in a combination, including each trailer, is inspected.
What is the difference between a pre-trip inspection and a DVIR?
The pre-trip inspection is the check a driver makes before driving, and no written record is required. The driver vehicle inspection report (DVIR) is a written report of defects, prepared at the end of each day's work. Under 49 CFR 396.11, no report is needed when the driver found no defect. The carrier keeps a report, its repair certification and the next driver's review for 3 months.
Who can do a DOT annual inspection?
Your own qualified inspector, or a commercial garage, fleet leasing company, truck stop or similar business that has the right facilities and qualified inspectors. Under 49 CFR 396.19, an inspector has either finished a federal- or state-sponsored training program or holds a state certificate, or has at least a year of training or experience as a commercial vehicle mechanic or inspector. A passing state inspection that meets Appendix A counts too.
How long do you keep DOT inspection records?
The annual inspection report is kept for 14 months from the inspection (396.21). Maintenance, inspection and repair records are kept for 1 year where the vehicle is housed or maintained, and for 6 months after it leaves your control (396.3). A DVIR with its repair certification is kept for 3 months (396.11).
Does a trailer need a DOT inspection?
Yes, when it is part of a commercial motor vehicle combination. The weight test uses the combination's rating, 10,001 pounds or more, and the vehicle must be used in interstate commerce. Under 49 CFR 396.17(a), each vehicle in a combination, including each trailer, is inspected, with its own proof of inspection. The rule doesn't separately address a trailer rated under 10,001 pounds, so ask FMCSA or your state, and until then inspect it with the truck.
What are the DOT roadside inspection levels?
The Commercial Vehicle Safety Alliance defines levels for roadside inspections. Level I checks the driver's credentials and the vehicle's brakes, cargo securement, coupling devices, frame, fuel, lights, steering, suspension, tires and wheels. Level II covers the same items, but only what can be inspected without getting under the vehicle. Level III checks the driver and paperwork only. Level V is a vehicle-only inspection with no driver present. A vehicle placed out of service can't be driven until the repairs are done.
Start from the work orders template
Get your own copy of a working work orders app with sample records, ready to make yours. Free to start.
Use the template, free